Wed, Nov 18
Partner Content

Put A Lid On It: Trenwa Composite Trench Covers from Fibrelite

Every substation, solar farm, and data center has a similar problem: trench covers that are hard to lift. Cables and conduit run below grade in precast trenches, and crews need to get to them for inspections, pulls and repairs.

When the lid is solid concrete or a steel plate, opening one section can mean a two-person job with a pry bar or a piece of lifting equipment. This costs additional time on every maintenance call. It also puts backs, fingers, and feet at risk along with steel adding a conductive surface risk next to energized equipment.

Trenwa's answer is the Fibrelite trench cover. A Fibrelite composite trench cover drops onto the Trenwa precast concrete trench and turns every access point into a quick, safe, manual lift.

A Partnership Built Around a Lid

Trenwa and UK-based Fibrelite, an OPW/Dover company, have worked together since 2014. Fibrelite custom-molds its composite covers to match Trenwa's existing precast trench profiles, so each cover seats correctly on the trench it was built for. The covers are sold exclusively through Trenwa in North America.

The material is a glass-reinforced polymer composite that is molded as a single piece. It doesn’t delaminate, rust, or chip, and carries real load at a fraction of the weight of concrete. Typical covers range in weight from 30 to 100 lbs., depending on size, and are one or two-person lifts.


Three Load Ratings

Fibrelite covers for Trenwa come in three series, so owners can match the cover to the traffic each run of trench actually sees.

Series

Load rating

Typical use

LPF Pedestrian

Pedestrian traffic only

Walkways and yard runs inside substations, plants and solar sites.

LMF Medium Duty

TIER 15 - Up to 15,000 lbs.

Areas with occasional light-vehicle traffic, such as pickups and utility vehicles.

LHF HS20

HS20, up to 20,000 lbs.

Road crossings and drive-over areas on precast concrete road-crossing trench.

LXF H40

HS40, up to 40,000 lbs.

Drive over areas for special equipment and cranes.


All three series are cut to Trenwa's precast concrete trench profiles, and molded-in logos, custom markings and custom colors are available.

  • Safer lifts. Covers come off by hand with Fibrelite's ergonomic lifting handle, cutting the risk of back strain and crushed fingers.

  • Non-conductive. Composite adds no conductive surface near energized equipment, a real advantage in substations and switchyards.

  • Built for harsh sites. The covers resist corrosion, most chemicals, heat, and freeze/thaw cycles. They won’t chip, crack or delaminate.

  • Sure footing. An anti-slip, anti-static top surface helps crews keep their footing in wet or icy conditions.

  • No scrap value. Composite gives thieves nothing to sell, unlike steel plate.

  • Maintenance-free. No painting, galvanizing, or patching over the life of the install.

Upgrading Your Trench Cover Has Never Been Easier

In 2017, Fibrelite and Trenwa developed covers specifically for customers replacing previously installed concrete and steel lids over existing Trenwa trenches. Every series is offered both for new installations and as an upgrade for older covers.

For owners with miles of buried precast already in place, the switch is simple. Remove the old lids and set the composite covers on the existing trench. The next time access is needed for the trench, it is a much easier process. 

Ready to Put a Lid on Your Next Project?

Explore the lightweight, non-conductive, custom-fit trench covers for Trenwa precast concrete trenches. Offering reliable performance with load ratings from pedestrian to HS20 traffic, the Fibrelite trench cover is ideal for both new construction and retrofit projects.

To size covers for your next project or existing trench upgrade, contact Trenwa at [email protected] or visit trenwa.com/trench-products.

1